Shipping Estimate
Country:
Region / State:
Post Code:

button_getquote

 

HW95-PG2(HW85,HW98) 12FPE Tune Kit

HW95-PG2(HW85,HW98) 12FPE Tune Kit
Product Code: 780120-28p200+3TC/12-KIT
Availability: 100
Price: $89.00

Available Options


* VacSEAL95:

Qty:     - OR -   Add to Wish List
Add to Compare

Included in the PG2-HW95 Module Kit (16 joles/12ft/lbs

The HW95 piston does not require the new cocking shoe however, it will make a difference if the new cocking shoe was added to the install. The PG2 is an all inclusive power module noise damping kit that is EZ to install, having a dual damping rear guide arrangement + a third guide top-hat arrangement opposite spring end, assembled valve quality spring, piston seal and multi use synthetic blend lubrication.
Performs exceptionally smooth during lock-up, and exceptionally quiet at moderate power during firing cycle!

780120-28p200
Drop-in, High Output tuning kit with exceptional smooth performance including our VacSEAL26 (95).
Easy DiY install.
Spring compressor may, or may not be needed.
Actual color of components may be different.

NOTE; HW BeemanHW 85 OLDER Guns. 
When using our PG2 module in old  HW85 air rifles prior to 2014,  it is Required that you the tuner Replace the cocking shoe with a NEW HW COCKING SHOE that RIDES on the compression tube SLOT!:
http://vortekproducts.com/ourstore/Seals-Tuning-Parts?http://vortekproducts.com/ourstore/Seals-Tuning-Parts?product_id=141
The OLD HW85 airgun has a slot milled ontop of the piston opposite of the cocking slotg. This short, atop slot (if one) HW85 piston slightly changes the cocking force angle and this change may/may not produce forces exceeding the PG2 rear guide causing damage. 

IMPORTANT TUNING NOTE FOR BAM B26 Airgun:
Though the B26 airguns have a 26mm compression tube they may not have the same size piston. Some customers communicated after opening up thier airgun realized  their B26 airgun piston was smaller in ID size compared to the HW95 piston, making the installing of the PG2 kit not workable.
We recommend the owners of the BAM B26 measure the ID size of piston before ordering.
The required inside piston diameter needs to measure a minimum of .866"/22mm.
Options would be to purchase a HW95 replacement piston from one of the Web Store distributors representing this product.

 

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Description

Included in the PG2-HW95 Module Kit (16 joles/12ft/lbs

The HW95 piston does not require the new cocking shoe however, it will make a difference if the new cocking shoe was added to the install. The PG2 is an all inclusive power module noise damping kit that is EZ to install, having a dual damping rear guide arrangement + a third guide top-hat arrangement opposite spring end, assembled valve quality spring, piston seal and multi use synthetic blend lubrication.
Performs exceptionally smooth during lock-up, and exceptionally quiet at moderate power during firing cycle!

780120-28p200
Drop-in, High Output tuning kit with exceptional smooth performance including our VacSEAL26 (95).
Easy DiY install.
Spring compressor may, or may not be needed.
Actual color of components may be different.

NOTE; HW BeemanHW 85 OLDER Guns. 
When using our PG2 module in old  HW85 air rifles prior to 2014,  it is Required that you the tuner Replace the cocking shoe with a NEW HW COCKING SHOE that RIDES on the compression tube SLOT!:
http://vortekproducts.com/ourstore/Seals-Tuning-Parts?http://vortekproducts.com/ourstore/Seals-Tuning-Parts?product_id=141
The OLD HW85 airgun has a slot milled ontop of the piston opposite of the cocking slotg. This short, atop slot (if one) HW85 piston slightly changes the cocking force angle and this change may/may not produce forces exceeding the PG2 rear guide causing damage. 

IMPORTANT TUNING NOTE FOR BAM B26 Airgun:
Though the B26 airguns have a 26mm compression tube they may not have the same size piston. Some customers communicated after opening up thier airgun realized  their B26 airgun piston was smaller in ID size compared to the HW95 piston, making the installing of the PG2 kit not workable.
We recommend the owners of the BAM B26 measure the ID size of piston before ordering.
The required inside piston diameter needs to measure a minimum of .866"/22mm.
Options would be to purchase a HW95 replacement piston from one of the Web Store distributors representing this product.

 

Reviews (2)

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Powered By OpenCart
Vortek Products Inc. © 2017 - Opencart Themes by Yoocart.net